smartctl version 5.0-24 Copyright (C) 2002 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: MAXTOR 4K080H4 Serial Number: 674119123435 Firmware Version: A08.1500 ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Off-line data collection status: (0x04) Offline data collection activity was suspended by an interrupting command from host. Self-test execution status: ( 89) The previous self-test completed having the electrical element of the test failed. Total time to complete off-line data collection: (2536) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Automatic timer ON/OFF support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 50) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail - 0 3 Spin_Up_Time 0x0027 074 074 020 Pre-fail - 3294 4 Start_Stop_Count 0x0032 100 100 008 Old_age - 32 5 Reallocated_Sector_Ct 0x0033 001 001 020 Pre-fail FAILING_NOW 499 7 Seek_Error_Rate 0x000b 100 001 023 Pre-fail In_the_past 0 9 Power_On_Hours 0x0012 086 086 001 Old_age - 9812 10 Spin_Retry_Count 0x0026 100 100 000 Old_age - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail - 0 12 Power_Cycle_Count 0x0032 100 100 008 Old_age - 32 13 Read_Soft_Error_Rate 0x000b 100 001 023 Pre-fail In_the_past 0 194 Temperature_Centigrade 0x0022 091 086 042 Old_age - 24 195 Hardware_ECC_Recovered 0x001a 006 004 000 Old_age - 417912090 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age - 0 197 Current_Pending_Sector 0x0032 033 032 020 Old_age - 338 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age - 0 SMART Error Log Version: 1 ATA Error Count: 20255 (device log contains only the most recent five errors) DCR = Device Control Register FR = Features Register SC = Sector Count Register SN = Sector Number Register CL = Cylinder Low Register CH = Cylinder High Register D/H = Device/Head Register CR = Content written to Command Register ER = Error register STA = Status register Timestamp is seconds since the previous disk power-on. Note: timestamp "wraps" after 2^32 msec = 49.710 days. Error 1 occurred at disk power-on lifetime: 9574 hours When the command that caused the error occurred, the device was in a vendor specific or reserved state. After command completion occurred, registers were: ER:40 SC:60 SN:b8 CL:c6 CH:02 D/H:e5 ST:d1 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 02 05 60 b8 c6 02 e5 c4 474.857 02 05 f8 20 c6 02 e5 c4 470.748 02 05 08 18 c6 02 e5 c4 470.746 00 00 f8 20 c5 02 e5 c4 470.732 00 00 08 18 c5 02 e5 c4 470.730 Error 2 occurred at disk power-on lifetime: 9574 hours When the command that caused the error occurred, the device was in a vendor specific or reserved state. After command completion occurred, registers were: ER:40 SC:68 SN:b0 CL:c6 CH:02 D/H:e5 ST:d1 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 02 05 f8 20 c6 02 e5 c4 470.748 02 05 08 18 c6 02 e5 c4 470.746 00 00 f8 20 c5 02 e5 c4 470.732 00 00 08 18 c5 02 e5 c4 470.730 02 05 f8 20 c4 02 e5 c4 470.717 Error 3 occurred at disk power-on lifetime: 9574 hours When the command that caused the error occurred, the device was in a vendor specific or reserved state. After command completion occurred, registers were: ER:40 SC:08 SN:c0 CL:3e CH:0e D/H:e5 ST:d1 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 0e 05 08 c0 3e 0e e5 c4 181.677 d0 04 08 b0 67 d0 e4 c5 181.651 0e 05 08 a0 45 0e e5 c4 181.646 0e 05 80 20 43 0e e5 c4 181.635 0e 05 80 20 41 0e e5 c4 181.622 Error 4 occurred at disk power-on lifetime: 9574 hours When the command that caused the error occurred, the device was in a vendor specific or reserved state. After command completion occurred, registers were: ER:40 SC:60 SN:c0 CL:3e CH:0e D/H:e5 ST:d1 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 0e 05 80 a0 3e 0e e5 c4 172.530 0e 05 80 20 3d 0e e5 c4 172.335 0e 05 80 20 3c 0e e5 c4 164.744 0e 05 10 10 3b 0e e5 c4 164.736 0e 05 f8 18 3a 0e e5 c4 157.202 Error 5 occurred at disk power-on lifetime: 9574 hours When the command that caused the error occurred, the device was in a vendor specific or reserved state. After command completion occurred, registers were: ER:40 SC:c0 SN:18 CL:04 CH:d3 D/H:e4 ST:d1 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp d3 04 c0 18 04 d3 e4 c4 502.837 d3 04 f8 e0 03 d3 e4 c4 498.739 d3 04 f8 e8 02 d3 e4 c4 498.716 55 01 c8 90 70 55 e1 c4 498.705 55 01 38 48 70 55 e1 c4 498.680 SMART Self-test log, version number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short off-line Completed: electrical failure 90% 9786 # 2 Extended captive Completed: servo/seek failure 90% 9676 0x04b7ed3d # 3 Extended captive Completed 00% 9575 # 4 Extended off-line Completed 00% 9432 # 5 Extended off-line Completed 00% 9415